ES12 Basics
A. LCD Display
B. Kickstand
C. Power Button
D. Club Selection Button
E. Blue Protective Boot
Note: After 8 minutes of idle time, the ES12
will automatically power off.
Welcome to the ES12 Portable Launch
Monitor. This Quick Start Guide explains how
to set up and use key features of the ES12
and Smartphone Application. Once you
understand the basics, you can download
the user manual and learn more about using
your ES12 at www.ernestsports.com/ES12
ES12 Quickstart Guide
Download the Ernest Sports App at the
Apple App Store
SM
or on Google Play
TM
.
Activate ES12. Use the 10 digit number
located on the front of this quick start guide
and/or the back of your ES12 device. This is
required to have full functionality of the app.
Note: For best results, place your phone on
a setting that does not idle or sleep after a
short amount of time. This may cause you
to lose connection with the app, and your
information will not be saved.
Once club selection has been made, place
the ES12 device 14” beside your ball and
14” downrange (see illustration below).
Extend the kickstand out of the back of
the ES12 using the the 60° leg. For some
higher loft wedges it may be necessary to
use the 45° leg. Position the ES12 on the
ground with the front of the device facing
downrange.
Once positioned the ES12 is ready for
stand alone use, or for connection to your
smartphone or tablet.
WELCOME
9:41 AM
NOTES
SCORE CARD
RANGE DATA
SETTINGS
VIDEO ANALYSIS
COURSE CADDY
Home
WEATHER
Positioning the ES12
Ernest Sports Application
14 “
14 “
To choose a club, press the Club Selection
button on the ES12.
The club selection will be displayed on the
LCD panel at the top of the ES12 device.
Continue to press the Club Selection button
until your desired club is shown on the LCD
panel.
The club notations are as follows:
Selecting a Club
CODE CLUB CODE CLUB
DrT Driver Total
3Wd 3 Wood
5Wd 5 Wood
HYB Hybrid
2Ir 2 Iron
3Ir 3 Iron
4Ir 4 Iron
5Ir 5 Iron
6Ir 6 Iron
7Ir 7 Iron
8Ir 8 Iron
9Ir 9 Iron
PW Pitching Wedge
GW Gap Wedge
SW Sand Wedge
LW Lob Wedge
Note: ES12
should face
toward target
Settings
New Range Session: Start a new ES12
range session.
Historical Range Data: View reports, club
gapping and club averages.
Weather: View local weather.
Video Analysis: Record, review and
analyze your golf swing.
Course Caddy: Use your range sessions
to help determine club use.
Notes: Take notes on your range session
and/or round of golf.
Skills Challenge: Test your skills hitting
target distances.
Settings: Set up Bluetooth and social
networking sites.
Tutorial: View the user manual.
App Welcome Page
LCD / Altitude
A00 Sea Level
A01 1000 ft. above sea level
A02 2000 ft. above sea level
A0X (X)000 ft. above sea level
Changing Settings. With the ES12 turned
OFF, press and hold the “Club” button, then
press the “Power” button and release both
buttons. The club button will be used to
change settings in each section, while the
power button will be used to move between
sections.
ALT. Select altitude based on the following
chart. Atlitude can be adjusted up to 9000 ft.
YRD or MTR. Select unit of measure
between YRD (yards and mph) or MTR
(meters and kph).
CAR or TOT. Select between CAR (carry
distance) and TOT (total distance).
PRG. Pressing the “Club” button will give you
the RST (reset) option. Warning: Pressing the
“Club” button again, will delete any pairings.
REV. Shows the software revision.
Apple Connecting
Apple Users: Initial pairing (and after
pairing reset) MUST be completed from
your Apple Bluetooth settings.
On your Apple device, go to “Settings”
> “Bluetooth”. Turn the Bluetooth ON.
Scan for devices. When found, select
ES12 connect.
For future connections, press and hold
the club button on the ES12; “PRG” will
blink, once blinking ends, your ES12
should be connected to your Apple
device.
Android Pairing
Android Users: Place the ES12 in
program mode by turning unit OFF.
Press and hold “Club” button, then
press the “Power” button once. Release
both buttons. Press the “Power” button
several times until the display reads
PRG. On your Android device, select the
ES12 app. Choose Settings > Set Up
Bluetooth > Bluetooth Settings > ON.
If the ES12 shows “Paired” already, then
delete (unpair) the current ES12. Now
scan for devices. From here, you will pair
with the ES12 (the ES12 will not show
the 6-digit pairing number). After pairing,
your Android device will show “Paired”
or “Paired but not connected”. Now exit
the programming mode by pressing the
power key several times until the ES12
shows the club.
Once paired, your Android device will
connect to the ES12 as needed unless
you reset the pairing on the ES12 or
unpair the Android device.
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern